CONTROLS/Tuning Adjustment - Revision history

Tanderson at 18:50, 4 September 2018

2018-09-04T18:50:16Z

2016-12-01T21:04:44Z

2016-11-21T22:42:45Z

2016-01-22T23:34:17Z

2016-01-22T23:32:16Z

2016-01-20T21:36:51Z

2016-01-20T21:36:39Z

2016-01-16T00:22:10Z

2016-01-16T00:11:23Z

2016-01-16T00:10:46Z

← Older revision		Revision as of 18:50, 4 September 2018
Line 1:		Line 1:
		+	{{Migrated\|printer-controls/index#tuning-adjustment}}
	{{DISPLAYTITLE:Tuning Adjustment}}__NOTOC__[[File:Tuning Adjustment-ss.png\|right\|framed\|<center>The '''Tuning Adjustment''' section of the Controls pane.</center>]]The Tuning Adjustment section of the Controls pane allows the user to change the speed and extrusion values during an active print.		{{DISPLAYTITLE:Tuning Adjustment}}__NOTOC__[[File:Tuning Adjustment-ss.png\|right\|framed\|<center>The '''Tuning Adjustment''' section of the Controls pane.</center>]]The Tuning Adjustment section of the Controls pane allows the user to change the speed and extrusion values during an active print.

@@ Line 16: / Line 16: @@
 When used during an active print, the extrusion multiplier modifies the extrusion flow rate (as defined in the [[#Formula|formula below]]).
-This variable is different from that of the [[Settings/Filament/Filament/Filament/Extrusion Multiplier|Extrusion Multiplier slice setting]] and will work in conjunction with it. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).
+This variable is different from that of the [[Settings/Filament/Extrusion/Flow/Extrusion Multiplier|Extrusion Multiplier slice setting]] and will work in conjunction with it. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).
 === Formula ===

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:Tuning Adjustment}}__NOTOC__[[File:Tuning Adjustment-ss.png|right|framed|<center>The '''Tuning Adjustment''' section of the Controls pane.</center>]]The Tuning Adjustment section of the Controls pane allows the user to change the speed and extrusion values during an active print.
-Use the slider or enter a value and click '''SET'''.
+Use the slider or enter a value and click '''Set'''.
 == Speed Multiplier ==

← Older revision		Revision as of 23:32, 22 January 2016
Line 1:		Line 1:
−	{{DISPLAYTITLE:Tuning Adjustment}}__NOTOC__[[File:Tuning Adjustment-ss.png\|right\|framed\|<center>The 'Tuning Adjustment' section of the Controls pane.</center>]]The Tuning Adjustment section of the Controls pane allows the user to change the speed and extrusion values during an active print.	+	{{DISPLAYTITLE:Tuning Adjustment}}__NOTOC__[[File:Tuning Adjustment-ss.png\|right\|framed\|<center>The '''Tuning Adjustment''' section of the Controls pane.</center>]]The Tuning Adjustment section of the Controls pane allows the user to change the speed and extrusion values during an active print.

	Use the slider or enter a value and click '''SET'''.		Use the slider or enter a value and click '''SET'''.

@@ Line 5: / Line 5: @@
 == Speed Multiplier ==
-When used during an active print, the speed multiplier modifies the speeds as set under the [[Slice Settings/General/Speed|Speed section in General settings]] by multiplying itself times each setting.
+When used during an active print, the speed multiplier modifies the speeds as set under the [[Settings/General/Speed|Speed section in General settings]] by multiplying itself times each setting.
 === Range ===

← Older revision	Revision as of 21:04, 1 December 2016
(No difference)

← Older revision		Revision as of 00:10, 16 January 2016
Line 1:		Line 1:
	{{DISPLAYTITLE:Tuning Adjustment}}		{{DISPLAYTITLE:Tuning Adjustment}}
		+
		+	__NOTOC__[[File:Tuning Adjustment-ss.png\|right\|framed\|<center>The 'Tuning Adjustment' section of the Controls pane.</center>]]The Tuning Adjustment section of the Controls pane allows the user to change the speed and extrusion values during an active print.
		+
		+	Use the slider or enter a value and click '''SET'''.
		+
		+	== Speed Multiplier ==
		+
		+	When used during an active print, the speed multiplier modifies the speeds as set under the [[Slice Settings/General/Speed\|Speed section in General settings]] by multiplying itself times each setting.
		+
		+	=== Range ===
		+
		+	*Low : 0.5
		+	*High : 2.0
		+
		+	== Extrusion Multiplier ==
		+
		+	When used during an active print, the extrusion multiplier modifies the extrusion flow rate (as defined in the [[#Formula\|formula below]]).
		+
		+	This variable is different from that of the [[Slice Settings/Filament/Filament/Filament/Extrusion Multiplier\|Extrusion Multiplier slice setting]] and will work in conjunction with it. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).
		+
		+	=== Formula ===
		+
		+	The general extrusion flow formula: <code>layer height / (filament area (pir²) '''extrusion multiplier''')</code>
		+
		+	=== Range ===
		+
		+	*Low : 0.5
		+	*High : 3.0

	[[Category:Controls]]		[[Category:Controls]]