Development/Adding New Slice Settings - Revision history

MatterHackers: MatterHackers moved page Adding New Slice Settings to Development/Adding New Slice Settings

2016-11-30T22:16:49Z

MatterHackers moved page Adding New Slice Settings to Development/Adding New Slice Settings

MatterHackers at 00:55, 18 August 2016

2016-08-18T00:55:32Z

MatterHackers at 00:57, 3 February 2016

2016-02-03T00:57:21Z

MatterHackers: Created page with "In MatterControl there are several files that are used to configure SliceSettings *'''StaticDataPrinterSettingsconfig.ini''' - This is the list of all possible printer settin..."

2015-12-15T22:57:20Z

Created page with "In MatterControl there are several files that are used to configure SliceSettings *'''StaticDataPrinterSettingsconfig.ini''' - This is the list of all possible printer settin..."

New page

In MatterControl there are several files that are used to configure SliceSettings

*'''StaticDataPrinterSettingsconfig.ini''' - This is the list of all possible printer settings. Your new type needs to be in here.
*'''StaticDataSliceSettingsLayouts.txt''' - This file describes where the setting will be laid out in the ui.
*'''StaticDataSliceSettingsProperties.txt''' - This file contains the description of the friendly name and the help for each setting.

== How to add a new setting ==

#Add the setting name to config.ini
#Put the setting name in the right place in Layouts.txt
#Add the friendly name and help text to Properties.txt

If the setting is also applicable to CuraEngine you need to write some code.

#Open - SlicerConfigurationSlicerMappingEngineMappingCura.cs
#Add the setting to curaToDefaultMapping. Write translation code if required

If the setting should not be available in Slic3r

#Open - SlicerConfigurationSlicerMappingEngineMappingSlic3r.cs
#Add the setting name to hideItems

[[Category:Development]]

@@ Line 1: / Line 1: @@
 In MatterControl there are several files that are used to configure SliceSettings
-*'''Static/DataPrinterSettings/config.ini''' - This is the list of all possible printer settings. Your new type needs to be in here.
+*'''StaticData/PrinterSettings/config.ini''' - This is the list of all possible printer settings. Your new type needs to be in here.
 *'''StaticData/SliceSettings/Layouts.txt''' - This file describes where the setting will be laid out in the ui.
 *'''StaticData/SliceSettings/Properties.txt''' - This file contains the description of the friendly name and the help for each setting.

← Older revision	Revision as of 22:16, 30 November 2016
(No difference)

@@ Line 1: / Line 1: @@
 In MatterControl there are several files that are used to configure SliceSettings
-*'''StaticDataPrinterSettingsconfig.ini''' - This is the list of all possible printer settings. Your new type needs to be in here.
+*'''Static/DataPrinterSettings/config.ini''' - This is the list of all possible printer settings. Your new type needs to be in here.
-*'''StaticDataSliceSettingsLayouts.txt''' - This file describes where the setting will be laid out in the ui.
+*'''StaticData/SliceSettings/Layouts.txt''' - This file describes where the setting will be laid out in the ui.
-*'''StaticDataSliceSettingsProperties.txt''' - This file contains the description of the friendly name and the help for each setting.
+*'''StaticData/SliceSettings/Properties.txt''' - This file contains the description of the friendly name and the help for each setting.
 == How to add a new setting ==
@@ Line 13: / Line 13: @@
 If the setting is also applicable to CuraEngine you need to write some code.
-#Open - SlicerConfigurationSlicerMappingEngineMappingCura.cs
+#Open - SlicerConfiguration/SlicerMapping/EngineMappingCura.cs
 #Add the setting to curaToDefaultMapping. Write translation code if required
 If the setting should not be available in Slic3r
-#Open - SlicerConfigurationSlicerMappingEngineMappingSlic3r.cs
+#Open - SlicerConfiguration/SlicerMapping/EngineMappingSlic3r.cs
 #Add the setting name to hideItems
 [[Category:Development]]