SETTINGS/Filament/Extrusion/Flow/Extrusion Multiplier - Revision history

Tanderson at 01:20, 6 April 2019

2019-04-06T01:20:14Z

MatterHackers: MatterHackers moved page Settings/Filament/Extrusion/Flow/Extrusion Multiplier to SETTINGS/Filament/Extrusion/Flow/Extrusion Multiplier

2016-12-01T20:37:36Z

MatterHackers moved page Settings/Filament/Extrusion/Flow/Extrusion Multiplier to SETTINGS/Filament/Extrusion/Flow/Extrusion Multiplier

MatterHackers: MatterHackers moved page Settings/Filament/Material/Properties/Extrusion Multiplier to Settings/Filament/Extrusion/Flow/Extrusion Multiplier without leaving a redirect

2016-11-15T17:29:31Z

MatterHackers moved page Settings/Filament/Material/Properties/Extrusion Multiplier to Settings/Filament/Extrusion/Flow/Extrusion Multiplier without leaving a redirect

MatterHackers: MatterHackers moved page Settings/Filament/Filament/Filament/Extrusion Multiplier to Settings/Filament/Material/Properties/Extrusion Multiplier

2016-11-15T01:51:57Z

MatterHackers moved page Settings/Filament/Filament/Filament/Extrusion Multiplier to Settings/Filament/Material/Properties/Extrusion Multiplier

MatterHackers: MatterHackers moved page Slice Settings/Filament/Filament/Filament/Extrusion Multiplier to Settings/Filament/Filament/Filament/Extrusion Multiplier

2016-01-20T20:54:25Z

MatterHackers moved page Slice Settings/Filament/Filament/Filament/Extrusion Multiplier to Settings/Filament/Filament/Filament/Extrusion Multiplier

MatterHackers at 00:08, 16 January 2016

2016-01-16T00:08:11Z

MatterHackers at 00:05, 16 January 2016

2016-01-16T00:05:45Z

MatterHackers at 23:56, 15 January 2016

2016-01-15T23:56:58Z

MatterHackers at 00:20, 24 December 2015

2015-12-24T00:20:37Z

MatterHackers: Created page with "{{Slice Settings |All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing..."

2015-12-24T00:07:24Z

Created page with "{{Slice Settings |All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing..."

New page

{{Slice Settings

|All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.

This value can also be adjusted during a print in real time using the [[Controls/Tuning Adjustment/Extrusion Multiplier|Extrusion Multiplier]] slider on the Controls pane. Keep in mind using the function in Controls will have an effect in addition to any existing multiplier used in the setting described on this page. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).|*multiplier|

=== multiplier ===

In this example, all extrusions will be multiplied by 1.04.}}

← Older revision		Revision as of 01:20, 6 April 2019
Line 1:		Line 1:
		+	{{Migrated\|slice-settings/filament/advanced#extrusion-multiplier}}
	{{Slice Settings		{{Slice Settings

@@ Line 5: / Line 5: @@
 This value can also be adjusted during a print using the [[Controls/Tuning Adjustment#Extrusion Multiplier|Extrusion Multiplier]] slider on the Controls pane. Keep in mind using the function in Controls will have an effect in addition to any existing multiplier used in the setting described on this page. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).
-=== Range ===
+=== Formula ===
-All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.
+The general extrusion flow formula: <code>layer height / (filament area (pi*r²) * '''extrusion multiplier''')</code>|*multiplier
-=== Formula ===
+=== Range ===
-The general extrusion flow formula: <code>layer height / (filament area (pi*r²) * '''extrusion multiplier''')</code>|*multiplier|
+Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.|
 === multiplier ===
 In this example, all extrusions will be multiplied by 1.04.}}

@@ Line 2: / Line 2: @@
 |A multiplier for modifying the extrusion flow rate.
 All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.
-This value can also be adjusted during a print using the [[Controls/Tuning Adjustment/Extrusion Multiplier|Extrusion Multiplier]] slider on the Controls pane. Keep in mind using the function in Controls will have an effect in addition to any existing multiplier used in the setting described on this page. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).
+=== Formula ===
-The general extrusion flow formula: <code>layer height / (filament area (pi*r²) * extrusion multiplier)</code>|*multiplier|
+The general extrusion flow formula: <code>layer height / (filament area (pi*r²) * '''extrusion multiplier''')</code>|*multiplier|
 === multiplier ===
 In this example, all extrusions will be multiplied by 1.04.}}

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

← Older revision	Revision as of 17:29, 15 November 2016
(No difference)

← Older revision	Revision as of 01:51, 15 November 2016
(No difference)

← Older revision	Revision as of 20:54, 20 January 2016
(No difference)

@@ Line 3: / Line 3: @@
 |All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.
-This value can also be adjusted during a print in real time using the [[Controls/Tuning Adjustment/Extrusion Multiplier|Extrusion Multiplier]] slider on the Controls pane. Keep in mind using the function in Controls will have an effect in addition to any existing multiplier used in the setting described on this page. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).|*multiplier|
+This value can also be adjusted during a print using the [[Controls/Tuning Adjustment/Extrusion Multiplier|Extrusion Multiplier]] slider on the Controls pane. Keep in mind using the function in Controls will have an effect in addition to any existing multiplier used in the setting described on this page. For example, if the slicer setting is set at 1.06 and then the slider in Controls is used during the print and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08).|*multiplier|
 === multiplier ===
 In this example, all extrusions will be multiplied by 1.04.}}