SETTINGS/General - Revision history

MatterHackers at 20:38, 1 December 2016

2016-12-01T20:38:54Z

2016-12-01T20:37:40Z

2016-11-23T01:50:26Z

2016-11-15T01:19:10Z

2016-02-10T00:01:42Z

2016-01-20T21:36:22Z

2016-01-20T20:55:37Z

MatterHackers moved page Slice Settings/General to Settings/General without leaving a redirect

2016-01-15T01:03:29Z

2015-12-18T18:22:06Z

2015-12-18T17:35:21Z

@@ Line 3: / Line 3: @@
 == Sections ==
-=== [[Settings/General/Layers-Surface|Layers / Surface]] ===
+=== [[SETTINGS/General/Layers-Surface|Layers / Surface]] ===
-=== [[Settings/General/Infill|Infill]] ===
+=== [[SETTINGS/General/Infill|Infill]] ===
-=== [[Settings/General/Speed|Speed]] ===
+=== [[SETTINGS/General/Speed|Speed]] ===
-=== [[Settings/General/Raft-Priming|Raft / Priming]] ===
+=== [[SETTINGS/General/Raft-Priming|Raft / Priming]] ===
-=== [[Settings/General/Support Material|Support Material]] ===
+=== [[SETTINGS/General/Support Material|Support Material]] ===
-=== [[Settings/General/Output Options|Output Options]] ===
+=== [[SETTINGS/General/Output Options|Output Options]] ===
-=== [[Settings/General/Multiple Extruders|Multiple Extruders]] ===
+=== [[SETTINGS/General/Multiple Extruders|Multiple Extruders]] ===
-=== [[Settings/General/Single Print|Single Print]] ===
+=== [[SETTINGS/General/Single Print|Single Print]] ===

@@ Line 1: / Line 1: @@
 __NOTOC__{{DISPLAYTITLE:General}}[[File:ss-{{SUBPAGENAME}}-ss.png|right|framed|<center>The '''{{SUBPAGENAME}}''' category of slice settings as seen in the MatterControl settings pane.</center>]]Slice Settings found under this category apply to how the prints look and are physically formed.
-== Sub-Categories ==
+== Sections ==
 === [[Settings/General/Layers-Surface|Layers / Surface]] ===

@@ Line 3: / Line 3: @@
 == Sub-Categories ==
-=== [[Settings/General/Layers-Surface|Layers/Surface]] ===
+=== [[Settings/General/Layers-Surface|Layers / Surface]] ===
 === [[Settings/General/Infill|Infill]] ===
 === [[Settings/General/Speed|Speed]] ===
-=== [[Settings/General/Skirt and Raft|Skirt and Raft]] ===
+=== [[Settings/General/Raft-Priming|Raft / Priming]] ===
 === [[Settings/General/Support Material|Support Material]] ===
 === [[Settings/General/Output Options|Output Options]] ===
 === [[Settings/General/Multiple Extruders|Multiple Extruders]] ===

← Older revision		Revision as of 00:01, 10 February 2016
Line 1:		Line 1:
−	__NOTOC__{{DISPLAYTITLE:General}}[[File:ss-{{SUBPAGENAME}}-ss.png\|right\|framed\|<center>The '{{SUBPAGENAME}}' category of slice settings as seen in the MatterControl settings pane.</center>]]Slice Settings found under this category apply to how the prints look and are physically formed.	+	__NOTOC__{{DISPLAYTITLE:General}}[[File:ss-{{SUBPAGENAME}}-ss.png\|right\|framed\|<center>The '''{{SUBPAGENAME}}''' category of slice settings as seen in the MatterControl settings pane.</center>]]Slice Settings found under this category apply to how the prints look and are physically formed.

	== Sub-Categories ==		== Sub-Categories ==

@@ Line 3: / Line 3: @@
 == Sub-Categories ==
-=== [[Slice_Settings/General/Layers-Surface|Layers/Surface]] ===
+=== [[Settings/General/Layers-Surface|Layers/Surface]] ===
-=== [[Slice_Settings/General/Infill|Infill]] ===
+=== [[Settings/General/Infill|Infill]] ===
-=== [[Slice_Settings/General/Speed|Speed]] ===
+=== [[Settings/General/Speed|Speed]] ===
-=== [[Slice_Settings/General/Skirt and Raft|Skirt and Raft]] ===
+=== [[Settings/General/Skirt and Raft|Skirt and Raft]] ===
-=== [[Slice_Settings/General/Support Material|Support Material]] ===
+=== [[Settings/General/Support Material|Support Material]] ===
-=== [[Slice_Settings/General/Output Options|Output Options]] ===
+=== [[Settings/General/Output Options|Output Options]] ===
-=== [[Slice_Settings/General/Multiple Extruders|Multiple Extruders]] ===
+=== [[Settings/General/Multiple Extruders|Multiple Extruders]] ===

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

← Older revision	Revision as of 20:55, 20 January 2016
(No difference)

← Older revision		Revision as of 01:03, 15 January 2016
Line 1:		Line 1:
−	__NOTOC__[[File:ss-{{SUBPAGENAME}}-ss.png\|right\|framed\|<center>The '{{SUBPAGENAME}}' category of slice settings as seen in the MatterControl settings pane.</center>]]Slice Settings found under this category apply to how the prints look and are physically formed.	+	__NOTOC__{{DISPLAYTITLE:General}}[[File:ss-{{SUBPAGENAME}}-ss.png\|right\|framed\|<center>The '{{SUBPAGENAME}}' category of slice settings as seen in the MatterControl settings pane.</center>]]Slice Settings found under this category apply to how the prints look and are physically formed.

	== Sub-Categories ==		== Sub-Categories ==

← Older revision		Revision as of 18:22, 18 December 2015
Line 1:		Line 1:
−	~~__NOTOC__Slice~~ Settings found under this category apply to how the prints look and are physically formed.	+	__NOTOC__[[File:ss-{{SUBPAGENAME}}-ss.png\|right\|framed\|<center>The '{{SUBPAGENAME}}' category of slice settings as seen in the MatterControl settings pane.</center>]]Slice Settings found under this category apply to how the prints look and are physically formed.

	== Sub-Categories ==		== Sub-Categories ==