SETTINGS/General/Layers-Surface/Layer Height/First Layer Height - Revision history

Tanderson at 18:07, 5 September 2018

2018-09-05T18:07:39Z

MatterHackers: MatterHackers moved page Settings/General/Layers-Surface/Layer Height/First Layer Height to SETTINGS/General/Layers-Surface/Layer Height/First Layer Height

2016-12-01T20:37:40Z

MatterHackers moved page Settings/General/Layers-Surface/Layer Height/First Layer Height to SETTINGS/General/Layers-Surface/Layer Height/First Layer Height

MatterHackers at 21:20, 1 August 2016

2016-08-01T21:20:58Z

MatterHackers: Text replacement - "[[Slice Settings/" to "[[Settings/"

2016-01-20T21:22:51Z

Text replacement - "[[Slice Settings/" to "[[Settings/"

MatterHackers: MatterHackers moved page Slice Settings/General/Layers-Surface/Layer Height/First Layer Height to Settings/General/Layers-Surface/Layer Height/First Layer Height without leaving a redirect

2016-01-20T20:55:38Z

MatterHackers moved page Slice Settings/General/Layers-Surface/Layer Height/First Layer Height to Settings/General/Layers-Surface/Layer Height/First Layer Height without leaving a redirect

MatterHackers at 20:58, 12 January 2016

2016-01-12T20:58:37Z

MatterHackers at 00:51, 22 December 2015

2015-12-22T00:51:48Z

MatterHackers at 00:50, 22 December 2015

2015-12-22T00:50:39Z

MatterHackers at 01:20, 19 December 2015

2015-12-19T01:20:21Z

MatterHackers: Created page with "{{Slice Settings |Sets the height of the first layer. It is often desirable to print a taller first layer to ensure a good solid adhesion to the build plate.|Millimeters or p..."

2015-12-17T22:43:51Z

Created page with "{{Slice Settings |Sets the height of the first layer. It is often desirable to print a taller first layer to ensure a good solid adhesion to the build plate.|Millimeters or p..."

New page

{{Slice Settings

|Sets the height of the first layer. It is often desirable to print a taller first layer to ensure a good solid adhesion to the build plate.|Millimeters or percentage|

=== mm ===

Used as the default if no parameter type is specified. Will create a first layer of the specified millimeters thick.}}

=== % ===

Must enter '%' after input to activate. Used to specify height of first layer relative to [[Layer Height]] as a percentage.

[[File:{{SUBPAGENAME}}-ss-ex1.png]]

← Older revision		Revision as of 18:07, 5 September 2018
Line 1:		Line 1:
		+	{{Migrated\|slice-settings/general/general#first-layer-thickness}}
	{{Slice Settings		{{Slice Settings

@@ Line 2: / Line 2: @@
 |The height of the first layer. A first layer taller than the default layer height can ensure good adhesion to the build plate.|*millimeters (mm)
-*percent (%)|
+*percent [of [[Settings/General/Layers-Surface/Layer Height/Layer Height|Layer Height]]] (%)|
 === mm ===

@@ Line 10: / Line 10: @@
 === % ===
-Must enter '%' after input to activate. Used to specify height of first layer relative to [[Slice Settings/General/Layers-Surface/Layer Height/Layer Height|Layer Height]] as a percentage.
+Must enter '%' after input to activate. Used to specify height of first layer relative to [[Settings/General/Layers-Surface/Layer Height/Layer Height|Layer Height]] as a percentage.
 [[File:{{SUBPAGENAME}}-ss-ex1.png]]

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|Sets the height of the first layer. It is often desirable to print a taller first layer to ensure a good solid adhesion to the build plate.|*millimeters (mm)
+|The height of the first layer. A first layer taller than the default layer height can ensure good adhesion to the build plate.|*millimeters (mm)
 *percent (%)|

@@ Line 2: / Line 2: @@
 |Sets the height of the first layer. It is often desirable to print a taller first layer to ensure a good solid adhesion to the build plate.|*millimeters (mm)
-*percentage (%)|
+*percent (%)|
 === mm ===

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

← Older revision	Revision as of 20:55, 20 January 2016
(No difference)