SETTINGS/General/Raft-Priming/Skirt/Minimum Extrusion Length - Revision history

Tanderson at 19:10, 14 September 2018

2018-09-14T19:10:10Z

2017-08-01T01:29:09Z

2017-01-18T20:14:32Z

2016-12-01T20:37:43Z

2016-11-17T20:07:11Z

2016-11-15T01:28:43Z

2016-11-15T00:52:21Z

2016-01-20T21:26:56Z

Text replacement - "[[Slice Settings/" to "[[Settings/"

2016-01-20T20:55:39Z

2016-01-12T22:40:53Z

← Older revision		Revision as of 19:10, 14 September 2018
Line 1:		Line 1:
		+	{{Migrated\|slice-settings/adhesion/skirt#minimum-extrusion-length}}
	{{Slice Settings		{{Slice Settings

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|The minimum length of filament to use to draw the priming loops [[Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a loop is shorter than this value.|*millimeters (mm)
+|The minimum length of filament to use to draw the [[SETTINGS/General/Raft-Priming/Priming/Loops|priming loops]]. Enough loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a loop is shorter than this value. This is the measurement of the filament going into the extruder, not the length of the loops being extruded. We recommend setting this to the length of your hot end's hot zone. For an E3D or similar hot end this will be about 15 mm|*millimeters (mm)
 Can be zero.|

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|The minimum length of filament to use drawing the skirt [[Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough skirt loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a skirt is shorter than this value.|*millimeters (mm)
+|The minimum length of filament to use to draw the priming loops [[Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a loop is shorter than this value.|*millimeters (mm)
 Can be zero.|

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|The minimum length of filament to use drawing the skirt [[Slice Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough skirt loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a skirt is shorter than this value.|*millimeters (mm)
+|The minimum length of filament to use drawing the skirt [[Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough skirt loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a skirt is shorter than this value.|*millimeters (mm)
 Can be zero.|

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|The minimum length of filament to use drawing the skirt [[Slice Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough skirt loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a skirt is shorter than the Minimum Extrusion Length.|*millimeters (mm)
+|The minimum length of filament to use drawing the skirt [[Slice Settings/General/Skirt_and_Raft/Skirt/Loops|loops]]. Enough skirt loops will be drawn to use this amount of filament, overriding the value set in Loops if the value in Loops will produce a skirt is shorter than this value.|*millimeters (mm)
 Can be zero.|

← Older revision	Revision as of 01:29, 1 August 2017
(No difference)

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

← Older revision	Revision as of 01:28, 15 November 2016
(No difference)

← Older revision	Revision as of 00:52, 15 November 2016
(No difference)

← Older revision	Revision as of 20:55, 20 January 2016
(No difference)