SETTINGS/Printer/Custom G-Code/Resume G-Code - Revision history

MatterHackers: MatterHackers moved page Settings/Printer/Custom G-Code/Resume G-Code to SETTINGS/Printer/Custom G-Code/Resume G-Code

2016-12-01T20:37:49Z

MatterHackers moved page Settings/Printer/Custom G-Code/Resume G-Code to SETTINGS/Printer/Custom G-Code/Resume G-Code

MatterHackers at 17:27, 12 October 2016

2016-10-12T17:27:48Z

MatterHackers at 17:53, 17 February 2016

2016-02-17T17:53:16Z

MatterHackers: MatterHackers moved page Slice Settings/Printer/Custom G-Code/Resume G-Code to Settings/Printer/Custom G-Code/Resume G-Code without leaving a redirect

2016-01-20T20:56:15Z

MatterHackers moved page Slice Settings/Printer/Custom G-Code/Resume G-Code to Settings/Printer/Custom G-Code/Resume G-Code without leaving a redirect

MatterHackers at 21:55, 13 January 2016

2016-01-13T21:55:56Z

MatterHackers at 21:55, 13 January 2016

2016-01-13T21:55:08Z

MatterHackers at 21:54, 13 January 2016

2016-01-13T21:54:24Z

MatterHackers: Created page with "{{Slice Settings |G-Code to be run when the print resumes after a pause.|*G-Code Will accept Custom G-Code variables.| === G-C..."

2016-01-13T21:50:19Z

Created page with "{{Slice Settings |G-Code to be run when the print resumes after a pause.|*G-Code Will accept Custom G-Code variables.| === G-C..."

New page

{{Slice Settings

|G-Code to be run when the print [[Resume button|resumes]] after a pause.|*G-Code

Will accept [[Custom_G-Code_Variables|Custom G-Code variables]].|

=== G-Code ===

In this example, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z10 E-10 F12000), then set coordinates to absolute positioning again (G90).}}

← Older revision		Revision as of 21:55, 13 January 2016
Line 7:		Line 7:
	=== G-Code ===		=== G-Code ===

−	In this example, when the 'Resume' button is pressed after the print has been paused, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 ~~Z10 E~~-10 F12000), then set coordinates to absolute positioning again (G90).}}	+	In this example, when the 'Resume' button is pressed after the print has been paused, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z-10 E10.8 F12000), then set coordinates to absolute positioning again (G90).}}

← Older revision		Revision as of 21:55, 13 January 2016
Line 7:		Line 7:
	=== G-Code ===		=== G-Code ===

−	In this example, when the 'Resume' button is pressed, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z10 E-10 F12000), then set coordinates to absolute positioning again (G90).}}	+	In this example, when the 'Resume' button is pressed after the print has been paused, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z10 E-10 F12000), then set coordinates to absolute positioning again (G90).}}

← Older revision		Revision as of 21:54, 13 January 2016
Line 7:		Line 7:
	=== G-Code ===		=== G-Code ===

−	In this example, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z10 E-10 F12000), then set coordinates to absolute positioning again (G90).}}	+	In this example, when the 'Resume' button is pressed, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z10 E-10 F12000), then set coordinates to absolute positioning again (G90).}}

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|G-Code to be run when the print [[Resume button|resumes]] after a pause.|*G-Code
+|G-Code to be run when the print [[Resume button|resumes]] after a pause.
 *[[Custom_G-Code_Variables|Custom G-Code variables]]

@@ Line 2: / Line 2: @@
 |G-Code to be run when the print [[Resume button|resumes]] after a pause.|*G-Code
-Will accept [[Custom_G-Code_Variables|Custom G-Code variables]].|
+All G-Code must be uppercase to function properly.|
 === G-Code ===
 In this example, when the 'Resume' button is pressed after the print has been paused, the printer will set coordinates relative to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z-10 E10.8 F12000), then set coordinates to absolute positioning again (G90).}}

← Older revision	Revision as of 20:56, 20 January 2016
(No difference)