SETTINGS/Printer/Print Leveling/Probe Settings/Z Offset - Revision history

MatterHackers at 21:53, 2 August 2017

2017-08-02T21:53:40Z

MatterHackers at 22:47, 1 August 2017

2017-08-01T22:47:37Z

Tanderson: Tanderson moved page SETTINGS/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width to SETTINGS/Printer/Print Leveling/Probe Settings/Z Offset

2017-08-01T17:31:58Z

Tanderson moved page SETTINGS/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width to SETTINGS/Printer/Print Leveling/Probe Settings/Z Offset

MatterHackers at 01:34, 7 December 2016

2016-12-07T01:34:33Z

MatterHackers at 01:27, 7 December 2016

2016-12-07T01:27:23Z

MatterHackers: MatterHackers moved page Settings/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width to SETTINGS/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width

2016-12-01T20:37:52Z

MatterHackers moved page Settings/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width to SETTINGS/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width

MatterHackers: MatterHackers moved page Slice Settings/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width to Settings/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width without leaving a redirect

2016-01-20T20:56:16Z

MatterHackers moved page Slice Settings/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width to Settings/Printer/Print Leveling/Probe Settings/Manual Probe Paper Width without leaving a redirect

MatterHackers: Created page with "{{Slice Settings |The thickness of the paper (or other calibration device) used to perform manual bed probe.|*millimeters (mm)| === mm === In this example, the paper to be..."

2016-01-13T19:31:19Z

Created page with "{{Slice Settings |The thickness of the paper (or other calibration device) used to perform manual bed probe.|*millimeters (mm)| === mm === In this example, the paper to be..."

New page

{{Slice Settings

|The thickness of the paper (or other calibration device) used to perform manual bed probe.|*millimeters (mm)|

=== mm ===

In this example, the paper to be used during the manual bed probe is 0.1 mm thick.}}

@@ Line 1: / Line 1: @@
 {{Slice Settings1
-|The thickness of the paper (or other calibration device) used to perform manual bed probe.
+|The vertical distance from the Z probe to the nozzle, in millimeters.
 === Restrictions ===
-*Not shown when [[SETTINGS/Printer/Features/Hardware/Has Hardware Leveling|Has Hardware Leveling]] is enabled as only one form of leveling can be used at a time.|*millimeters (mm)|
+*Not shown when [[SETTINGS/Printer/Features/Hardware/Has Hardware Leveling|Has Hardware Leveling]] is enabled.|*millimeters (mm)|
 === mm ===
-In this example, the paper to be used during the manual bed probe is 0.1 mm thick.}}
+In this example, the Z probe is 1.6mm higher than the nozzle.}}

← Older revision		Revision as of 22:47, 1 August 2017
Line 1:		Line 1:
−	{{Slice ~~Settings~~	+	{{Slice Settings1

	\|The thickness of the paper (or other calibration device) used to perform manual bed probe.		\|The thickness of the paper (or other calibration device) used to perform manual bed probe.

@@ Line 5: / Line 5: @@
 === Restrictions ===
-*This section (Print Recovery) is not shown when [[SETTINGS/Printer/Features/Hardware/Has Hardware Leveling|Has Hardware Leveling]] is enabled as only one form of leveling can be used at a time.|*millimeters (mm)|
+*Not shown when [[SETTINGS/Printer/Features/Hardware/Has Hardware Leveling|Has Hardware Leveling]] is enabled as only one form of leveling can be used at a time.|*millimeters (mm)|
 === mm ===
 In this example, the paper to be used during the manual bed probe is 0.1 mm thick.}}

← Older revision	Revision as of 17:31, 1 August 2017
(No difference)

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

← Older revision	Revision as of 20:56, 20 January 2016
(No difference)