SETTINGS/Printer/Print Recovery/Recover Settings/XY Homing Position - Revision history

MatterHackers at 01:32, 7 December 2016

2016-12-07T01:32:56Z

MatterHackers at 01:23, 7 December 2016

2016-12-07T01:23:34Z

MatterHackers: MatterHackers moved page Settings/Printer/Print Recovery/Recover Settings/XY Homing Position to SETTINGS/Printer/Print Recovery/Recover Settings/XY Homing Position

2016-12-01T20:37:52Z

MatterHackers moved page Settings/Printer/Print Recovery/Recover Settings/XY Homing Position to SETTINGS/Printer/Print Recovery/Recover Settings/XY Homing Position

MatterHackers at 00:49, 23 November 2016

2016-11-23T00:49:01Z

MatterHackers at 00:36, 23 November 2016

2016-11-23T00:36:31Z

MatterHackers: Created page with "{{Slice Settings |Function text|*parameters text| === Parameter 1 === Caption for Example for Parameter 1.}} === Parameter 2 === Caption for example for Parameter 2. F..."

2016-11-15T18:32:45Z

Created page with "{{Slice Settings |Function text|*parameters text| === Parameter 1 === Caption for Example for Parameter 1.}} === Parameter 2 === Caption for example for Parameter 2. F..."

New page

{{Slice Settings

|Function text|*parameters text|

=== Parameter 1 ===

Caption for Example for Parameter 1.}}

=== Parameter 2 ===

Caption for example for Parameter 2.

[[File:{{SUBPAGENAME}}-ss-ex1.png]]

[[Category:Incomplete]]

@@ Line 3: / Line 3: @@
 |Specify the X and Y coordinates where the printer can home the Z axis without interfering with the partially-completed print.
-Note: Not shown when [[SETTINGS/Printer/Features/Hardware/Has Hardware Leveling|Has Hardware Leveling]] is enabled as G29 procedures could interfere with a partially-completed print.
+=== Restrictions ===
-Note: Not shown when [[SETTINGS/Printer/Features/Behavior/Home Z Max|Home Z Max]] is enabled as homing up would not interfere with a partially-completed print.|*millimeters (mm)|
+*Not shown when [[SETTINGS/Printer/Features/Hardware/Has Hardware Leveling|Has Hardware Leveling]] is enabled as G29 procedures could interfere with a partially-completed print.
 === mm ===
 In this example, the best coordinates on the X and Y axes for the printer to home the Z axis are 185, 190.}}

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|Specify the X and Y coordinates where the printer can home the Z axis without interfering with the partially-completed print.|*millimeters (mm)|
+|Specify the X and Y coordinates where the printer can home the Z axis without interfering with the partially-completed print.
 === mm ===
 In this example, the best coordinates on the X and Y axes for the printer to home the Z axis are 185, 190.}}

← Older revision		Revision as of 00:49, 23 November 2016
Line 5:		Line 5:
	=== mm ===		=== mm ===

−	In this example, the best coordinates on the X and Y axes for the printer to home the Z axis are ~~600~~, ~~750~~.}}	+	In this example, the best coordinates on the X and Y axes for the printer to home the Z axis are 185, 190.}}

← Older revision	Revision as of 20:37, 1 December 2016
(No difference)

@@ Line 1: / Line 1: @@
 {{Slice Settings
-|Function text|*parameters text|
+|Specify the X and Y coordinates where the printer can home the Z axis without interfering with the partially-completed print.|*millimeters (mm)|
-=== Parameter 1 ===
+=== mm ===
-Caption for Example for Parameter 1.}}
+In this example, the best coordinates on the X and Y axes for the printer to home the Z axis are 600, 750.}}
-−
-=== Parameter 2 ===
-−
-Caption for example for Parameter 2.
-−
-[[File:{{SUBPAGENAME}}-ss-ex1.png]]
-−
-[[Category:Incomplete]]