Difference between revisions of "CONTROLS/Macros"
From MatterControl Manual
< CONTROLS
(→Commands) |
|||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Migrated|printer-controls/macros}} | ||
__NOTOC__{{DISPLAYTITLE:Macros}}Macros are snippets of saved code which can be called with the click of a button instead of having to be typed repeatedly. | __NOTOC__{{DISPLAYTITLE:Macros}}Macros are snippets of saved code which can be called with the click of a button instead of having to be typed repeatedly. | ||
| Line 49: | Line 50: | ||
Click the '''Cancel''' button to discard changes. | Click the '''Cancel''' button to discard changes. | ||
| − | == Macro Scripting == | + | == Macro Scripting (Starting in version 1.7) == |
Macro Scripting allows for the use of advanced functions in macros. These functions are called by using commands. | Macro Scripting allows for the use of advanced functions in macros. These functions are called by using commands. | ||
| Line 57: | Line 58: | ||
To use a macro scripting command, begin the line with the following function: | To use a macro scripting command, begin the line with the following function: | ||
| − | <code>; | + | <code>; host.:</code> |
Then add a command and any applicable parameters. | Then add a command and any applicable parameters. | ||
| − | <code>; | + | <code>; command([parameters])"</code> |
The result should look something like this: | The result should look something like this: | ||
| − | <code>; | + | <code>; host.show_message(title:"Waiting for extruder to heat to [temperature].")</code> |
=== Commands === | === Commands === | ||
| − | <code> | + | <code>ding()</code> |
| − | + | Play a bell sound. | |
| − | + | <code>show_message()</code> | |
| − | + | Shows the specified message. | |
| − | + | ||
| − | <code> | + | Optional parameter variables (content must be in quotes): |
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! Parameter || Description || Example | ||
| + | |- | ||
| + | | title || Main text to show || <pre>title:"Trim Filament"</pre> | ||
| + | |- | ||
| + | | markdown || The contents of the message in Markdown formatted text. May contain images from the internet. Use <br> for line breaks || <pre>markdown:"Trim the end of the filament to ensure a good load.<br><br>Make sure you trim it at a slight angle."</pre> | ||
| + | |- | ||
| + | | wait_ok || Script execution will wait for the user to click 'Continue' || <pre>wait_ok:"true"</pre> | ||
| + | |- | ||
| + | | repeat_gcode || G-Code to repeat until expire time reached. Lines can be separated with a <nowiki>|</nowiki>. || <pre>repeat_gcode:"G1 E.1 F150|G4 P10"</pre> | ||
| + | |- | ||
| + | | expire || The max amount of time to run repeate_gcode or show this message (seconds) || <pre>expire:"300"</pre> | ||
| + | |- | ||
| + | | count_down || Show a timer counting down from this time || <pre>count_down:"28"</pre> | ||
| + | |} | ||
| + | |||
| + | <code>choose_material</code> | ||
Shows the choose material window. | Shows the choose material window. | ||
| − | + | Optional parameter variables (content must be in quotes): | |
| − | + | *title: [main text to show] | |
=== Example Script === | === Example Script === | ||
| − | The following | + | The following is an example of a script used for loading filament: |
| − | <pre>; | + | <pre>; host.choose_material(title:"Choose the material that you are loading.") |
| − | |||
M104 S[temperature] ; start heating up the extruder | M104 S[temperature] ; start heating up the extruder | ||
| + | |||
| + | ; host.show_message(title:"Trim the end of the filament to ensure a good load.", image:"https://cdn.instructables.com/FSW/FEGA/HN4ZL57T/FSWFEGAHN4ZL57T.MEDIUM.jpg", wait_ok:"true") | ||
M302 S0 ; Allow extrusion at any temperature | M302 S0 ; Allow extrusion at any temperature | ||
| − | ; | + | G91 ; Relative positioning |
| − | ; | + | ; host.show_message(title:"Put filament into extruder and click Continue.", repeat_gcode:"G1 E.1 F150|G4 P10", expire:"90", image:"https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/5035400628/original/20150903_115628.jpg?1441307271") |
| + | G90 ; Absolute positioning | ||
| + | ; host.show_message(title:"Loading filament...", count_down:"28") | ||
G92 E0 ; reset the extruder position to 0 | G92 E0 ; reset the extruder position to 0 | ||
G91 ; Relative positioning | G91 ; Relative positioning | ||
| Line 108: | Line 129: | ||
M302 S150 ; Set cold extrude temp back to reasonable | M302 S150 ; Set cold extrude temp back to reasonable | ||
| − | ; | + | ; host.show_message(title:"Waiting for extruder to heat to [temperature].") |
M109 S[temperature] ; heat up the extruder | M109 S[temperature] ; heat up the extruder | ||
| − | |||
; extrude slowly so that we can prime the extruder | ; extrude slowly so that we can prime the extruder | ||
| − | + | ; host.show_message(title:"Click 'Continue' when filament is running cleanly.", repeat_gcode:"G1 E1 F300|G4 P10", expire:"90") | |
G4 S1 ; wait for move to finish | G4 S1 ; wait for move to finish | ||
| Line 119: | Line 139: | ||
G92 E0 ; reset the extruder position to 0 | G92 E0 ; reset the extruder position to 0 | ||
| − | M104 S0 ; turn the extruder | + | M104 S0 ; turn the extruder temperature off |
| + | </pre> | ||
[[Category:Controls]] | [[Category:Controls]] | ||
[[Category:Features]] | [[Category:Features]] | ||
Latest revision as of 10:55, 4 September 2018
|
|
Migrating: For MatterControl 2.0 the MatterControl documentation is moving to matterhackers.com/mattercontrol/support/. |
Macros are snippets of saved code which can be called with the click of a button instead of having to be typed repeatedly.
The Macros of the Controls pane section is where the user creates and stores these macros.
To learn more about G-Code and its utility in 3D printing, check out this resource: http://reprap.org/wiki/G-code
Macros Pane
The screenshot to the right shows an example of several macro buttons for the Rostock MAX V2.
Macro Editor
) next to the word Macros. This will open the Macro Presets window.
Macro Presets Window
Add
To add a new Macro, click the Add button. This will open the Edit Macro window.
Close
Click the Close button to close the window and return to the main screen.
Edit Macro Window
Macro Name
Enter a unique name for the macro.
Macro Commands
Enter G-Code command(s) in this field.
Can be multiple lines long.
Save
Click the Save button to add the button to the Macros section.
Cancel
Click the Cancel button to discard changes.
Macro Scripting (Starting in version 1.7)
Macro Scripting allows for the use of advanced functions in macros. These functions are called by using commands.
Syntax
To use a macro scripting command, begin the line with the following function:
; host.:
Then add a command and any applicable parameters.
; command([parameters])"
The result should look something like this:
; host.show_message(title:"Waiting for extruder to heat to [temperature].")
Commands
ding()
Play a bell sound.
show_message()
Shows the specified message.
Optional parameter variables (content must be in quotes):
| Parameter | Description | Example |
|---|---|---|
| title | Main text to show | title:"Trim Filament" |
| markdown | The contents of the message in Markdown formatted text. May contain images from the internet. Use for line breaks |
markdown:"Trim the end of the filament to ensure a good load.<br><br>Make sure you trim it at a slight angle." |
| wait_ok | Script execution will wait for the user to click 'Continue' | wait_ok:"true" |
| repeat_gcode | G-Code to repeat until expire time reached. Lines can be separated with a |. | repeat_gcode:"G1 E.1 F150|G4 P10" |
| expire | The max amount of time to run repeate_gcode or show this message (seconds) | expire:"300" |
| count_down | Show a timer counting down from this time | count_down:"28" |
choose_material
Shows the choose material window.
Optional parameter variables (content must be in quotes):
- title: [main text to show]
Example Script
The following is an example of a script used for loading filament:
; host.choose_material(title:"Choose the material that you are loading.") M104 S[temperature] ; start heating up the extruder ; host.show_message(title:"Trim the end of the filament to ensure a good load.", image:"https://cdn.instructables.com/FSW/FEGA/HN4ZL57T/FSWFEGAHN4ZL57T.MEDIUM.jpg", wait_ok:"true") M302 S0 ; Allow extrusion at any temperature G91 ; Relative positioning ; host.show_message(title:"Put filament into extruder and click Continue.", repeat_gcode:"G1 E.1 F150|G4 P10", expire:"90", image:"https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/5035400628/original/20150903_115628.jpg?1441307271") G90 ; Absolute positioning ; host.show_message(title:"Loading filament...", count_down:"28") G92 E0 ; reset the extruder position to 0 G91 ; Relative positioning G1 E100 F1200 ; extrude the filament G1 E100 F1200 ; extrude the filament G1 E100 F1200 ; extrude the filament G1 E100 F1200 ; extrude the filament G1 E100 F1200 ; extrude the filament G4 S1 ; wait for move to finish M302 S150 ; Set cold extrude temp back to reasonable ; host.show_message(title:"Waiting for extruder to heat to [temperature].") M109 S[temperature] ; heat up the extruder ; extrude slowly so that we can prime the extruder ; host.show_message(title:"Click 'Continue' when filament is running cleanly.", repeat_gcode:"G1 E1 F300|G4 P10", expire:"90") G4 S1 ; wait for move to finish G90 ; Absolute positioning G92 E0 ; reset the extruder position to 0 M104 S0 ; turn the extruder temperature off
