Difference between revisions of "Error Messages"

Revision as of 17:10, 2 February 2016

Queue Errors

Too Big to Render

Cause: This error message is in reference to the size of the STL file, not the physical dimensions of the part. Your part is probably either very complicated or has an excessive amount of detail, resulting in a large file size. It will still print, however you will not be able to preview it beforehand.

Solution: Reduce the number of polygons in the model. Reducing larger models (250,000+ polygons) to 100,000 generally allows them to slice well and causes no significant loss to printable resolution. Here's a link to a good tutorial using Meshlab: http://www.shapeways.com/tutorials/polygon_reduction_with_meshlab

Slice Errors

Slice Error Review Settings

Cause: Occurs when one or more slicer settings are invalid. Also a known issue with certain versions of Slic3r.

Possible Solutions:

• Review settings for any invalid parameters.
• Try a different Slice Engine
• Use a previous version of MatterControl like 1.3: Release Notes#1.3.0

'Layer Height' must be less than or equal to the 'Nozzle Diameter'.

Cause: The Layer Height is set to a value greater than the Nozzle Diameter.

Solution: Set Layer Height to a value less than or equal to Nozzle Diameter.

'First Layer Height' must be less than or equal to the 'Nozzle Diameter'.

Cause: The First Layer Height is set to a value greater than the Nozzle Diameter.

Solution: Set First Layer Height to a value less than or equal to Nozzle Diameter.

'First Layer Extrusion Width' must be less than or equal to the 'Nozzle Diameter' * 4.

Cause: The First Layer Extrusion Width is set to a value greater than 4 times the Nozzle Diameter.

Solution: Set First Layer Extrusion Width to a value less than or equal to 4 times the Nozzle Diameter.

'First Layer Extrusion Width' must be greater than 0.

Cause: The First Layer Extrusion Width is set to a value of 0 or less.

Solution: Set First Layer Extrusion Width to a value greater than 0.

The Minimum Fan Speed can only go as high as 100%.

Cause: The Minimum Fan Speed is set to a value greater than 100%.

Solution: Set Minimum Fan Speed to a value of 0-100%.

The Maximum Fan Speed can only go as high as 100%.

Cause: The Maximum Fan Speed is set to a value greater than 100%.

Solution: Set Maximum Fan Speed to a value of 0-100%.

The Extruder Count must be at least 1.

Cause: The Extruder Count is set to a value less than 1.

Solution: Set Extruder Count to a value of 1 or more.

The Fill Density must be between 0 and 1.

Cause: The Fill Density is set to a value less than 0 or greater than 100% (or 1, if using ratio).

Solution: Set Fill Density to a value greater than 0 and less than or equal to 100% (or 1, if using ratio).

Solid Infill works best when set to LINES.

Cause: The Infill Type selected is not compatible with solid infill and will causing extrusion issues.

Solution: Either set Infill Type to LINES or change the Fill Density to a value less than 100% (or 1, if using ratio).

Login/Account Errors

Oops! Invalid username, email or password.

Cause: The username, email, or password entered does not match any on file.

Solution: Enter a valid username, email, or password.

Oops! There was a problem processing your request.

Cause: A system error occurred during the password change process.

Solution: Wait a few minutes and try again. If the problem persists, contact MatterControl support.

Oops! There was a problem creating your account.

Cause: A system error occurred and the account creation process was not completed.

Solution: Wait a few minutes and try again. If the problem persists, contact MatterControl support.

Oops! There was a problem resetting your password.

Cause: A system error occurred and the password reset process was not completed.

Solution: Wait a few minutes and try again. If the problem persists, contact MatterControl support.

Oops! There was a problem updating your password.

Cause: A system error occurred and the password update process was not completed.

Solution: Wait a few minutes and try again. If the problem persists, contact MatterControl support.

Sorry! Unable to connect to server. Please try again later.

Cause: MatterControl is not able to establish a connection to its cloud servers. Possible Internet connection failure.

Solution: Check Internet connection. Visit http://sync.mattercontrol.com/ in a web browser to verify that the servers are online.

Sorry! Too many login attempts. Please try again later.

Cause: MatterControl allows only a certain number of login attempts in a given time frame, and that number has been exceeded.

Solution: Wait a few minutes and try again with the correct credentials.

Sorry! Looks like an account already exists for that username.

Cause: The username is in use by another user.

Solution: Choose a different username.

Sorry! We couldn't find that account.

Cause: The account information entered does not match our records.

Solution: Provide correct information.

Sorry! Looks like that reset code has expired.

Cause: The reset code entered is no longer valid.

Solution: Reset the password again.

Sorry! Looks like that reset code is invalid.

Cause: An invalid reset code was entered.

Solution: Use the correct code.

Uh oh! Passwords do not match.

Cause: The two passwords entered do not match.

Solution: Type both passwords correctly.