User contributions
22 December 2015
File:Support Type-ss-ex1.png
no edit summary
File:Support Type-ss-ex.png
MatterHackers uploaded a new version of File:Support Type-ss-ex.png
File:Support test.stl
no edit summary
21 December 2015
SETTINGS/General/Support Material/Support Material/Generate Support Material
Created page with "{{Slice Settings |Allows for the generation of support material.|*Boolean| === Boolean === The check box is checked to use the function.}} The check box is unchecked to le..."
File:Air Gap1-ss.png
User created page with UploadWizard
File:X and Y Distance-ss.png
User created page with UploadWizard
File:Support Type-ss-ex.png
User created page with UploadWizard
File:Support Type-ss.png
User created page with UploadWizard
File:Support Material-category1.png
User created page with UploadWizard
File:Support Material Extruder-ss.png
User created page with UploadWizard
File:Support Interface Extruder-ss.png
User created page with UploadWizard
File:Support Everywhere-ss.png
User created page with UploadWizard
File:Pattern Spacing-ss.png
User created page with UploadWizard
File:Interface Layers-ss.png
User created page with UploadWizard
File:Infill Angle-ss.png
User created page with UploadWizard
File:Generate Support Material-ss-ex1.png
User created page with UploadWizard
File:Generate Support Material-ss-ex.png
User created page with UploadWizard
File:Generate Support Material-ss.png
User created page with UploadWizard
File:Amount-ss-ex.png
User created page with UploadWizard
File:Amount-ss.png
User created page with UploadWizard
File:Support Material-subsection.png
no edit summary
File:Advanced-subsection.png
no edit summary
File:Infill-subsection.png
no edit summary
SETTINGS/General/Raft-Priming/Raft/Raft Extruder
Created page with "{{Slice Settings |The index of the extruder to use to print the raft.|*extruder index value| === extruder index value === The second extruder (1) will be..."
SETTINGS/General/Raft-Priming/Raft/Fan Speed
Created page with "{{Slice Settings |The speed at which the cooling fan(s) will run during the printing of the raft, expressed as a percentage.|*percent (%) While the value can be any whole nu..."
SETTINGS/General/Speed/Modifiers/First Layer Speed
no edit summary
-5
SETTINGS/General/Speed/Speed for Perimeters/Outside Perimeter
no edit summary
-3
SETTINGS/General/Speed/Speed for Infill/Raft
no edit summary
-3
SETTINGS/General/Speed/Speed for Infill/Top Solid Infill
no edit summary
-3
SETTINGS/General/Infill/Infill/Fill Density
no edit summary
+2
SETTINGS/General/Infill/Infill/Fill Density
no edit summary
-3
SETTINGS/General/Layers-Surface/Layer Height/First Layer Height
no edit summary
+64
SETTINGS/General/Layers-Surface/Layer Height/First Layer Height
no edit summary
-3
SETTINGS/General/Raft-Priming/Raft/Air Gap
Created page with "{{Slice Settings |The distance between the first layer and the top of the raft. A good value is typically about half the Slice Settings/Printer/Extruder/Extruder X/Nozzle D..."
File:Air Gap-ss.png
MatterHackers uploaded a new version of File:Air Gap-ss.png
SETTINGS/General/Raft-Priming/Raft/Expand Distance
Created page with "{{Slice Settings |The extra distance the raft will extend around the edge of the part.|*millimeters (mm)| === mm === In this example, the raft will extend out 5 mm from aro..."
File:Raft Extruder-ss-ex.png
MatterHackers uploaded a new version of File:Raft Extruder-ss-ex.png
File:Raft-subsection.png
no edit summary
SETTINGS/General/Raft-Priming/Raft/Create Raft
Created page with "{{Slice Settings |Allows for the creation of a raft. Useful to prevent warping when printing ABS (and other warping-prone plastics) as it helps parts adhere to the bed.|*Bool..."
File:Create Raft-ss-ex.png
MatterHackers uploaded a new version of File:Create Raft-ss-ex.png
File:Create Raft-ss-ex.png
no edit summary
File:Create Raft-ss-ex1.png
MatterHackers moved page File:Create Raft-ss-ex.png to File:Create Raft-ss-ex1.png without leaving a redirect
mFile:Skirt-subsection.png
no edit summary
SETTINGS/General/Raft-Priming/Skirt/Minimum Extrusion Length
Created page with "{{Slice Settings |The minimum length of filament to use drawing the skirt loops. Enough skirt loops will be drawn to use..."
SETTINGS/General/Raft-Priming/Skirt/Distance From Object
Created page with "{{Slice Settings |The distance from the model at which the first skirt loop is drawn. Make this 0 to create an anchor for the part to the bed, or brim.|*millimeters (mm) Can..."
SETTINGS/General/Infill/Infill/Fill Density
no edit summary
+2
File:Distance From Object-ss.png
MatterHackers moved page File:Distance from Object-ss.png to File:Distance From Object-ss.png without leaving a redirect
mFile:Distance From Object-ss-ex.png
MatterHackers moved page File:Distance from Object-ss-ex.png to File:Distance From Object-ss-ex.png without leaving a redirect
mSETTINGS/General/Raft-Priming/Skirt/Distance or Loops
no edit summary
+111
SETTINGS/General/Raft-Priming/Skirt/Distance or Loops
Created page with "{{Slice Settings |The number of loops to draw around all the parts on the bed.|*count| === count === In this example, three loops will be drawn around the model.}}"