__NOTOC__
The slice settings for Cura in MatterControl are divided by three categories:
* '''Print''': This is where the settings concerning the actual printed part are located. Things like, layer height, support material, and infill.
* '''Filament''': This is where the settings concerning the filament are located. Things like temperature control and cooling.
* '''Printer''': This is where settings concerning the actual hardware are located. Things like bed size, nozzle diameter, and custom GCode.
We'll be breaking them down by sub-category, in order, assuming that [[Getting_Started#Show_All_Settings_.2F_User_Level_.28Basic.2C_Intermediate.2C_Advanced.29|Advanced mode]] is enabled. If a setting isn't visible, make sure [[Getting_Started#Show_All_Settings_.2F_User_Level_.28Basic.2C_Intermediate.2C_Advanced.29|Advanced mode]] is enabled.
= General =
== Layers/Perimeters ==
=== '''''Layer Height''''' ===
:'''Layer Height:''' This determines the quality of the print in its entirety. The thinner the layer, the higher the resolution. This also is the biggest factor when determining print time.
:'''First Layer Height:''' This determines the height of your first layer, which is useful in making sure your print has a good starting point. Remember, the vast majority of prints will fail within the first layer.
=== '''''Vertical Shells''''' ===
:'''Perimeters (minimum):''' This determines how many vertical layers you have on your print. i.e. how thick your walls will be.
:'''Spiral Vase:''' Force the print to have only one vertical layer and gradually increase the extruder height during the print. Only one part can be printed at a time with this feature.
=== '''''Horizontal Shells''''' ===
:'''Number of Solid Layers on the Top:''' This determines how many of the top layers will be solid. This is useful when the [[infill]] is lower.
:'''Number of Solid Layers on the Bottom:''' This determines how many solid layers will be printed before the printer begins to use [[infill]].
== Infill ==
=== '''''Infill''''' ===
:'''Fill Density:''' This determines the density of your infill within the print. This affects print time, total weight, and filament used.
== Speed ==
=== '''''Speed for Print Moves''''' ===
:'''Perimeters:''' This determines how fast your printer will travel when extruding perimeters.
:'''Infill:''' This determines how fast your printer will travel when extruding infill.
=== '''''Speed for non Print Moves''''' ===
:'''Travel:''' How fast your printer will move when it is '''not''' otherwise extruding.
=== '''''Modifiers''''' ===
:'''First Layer Speed:''' This determines how fast the printer will extrude during the first layer. This is typically a percentage of the previous settings, as extruding the first layer more slowly helps the print get started.
== Skirt and Brim ==
=== '''''Skirt''''' ===
:'''Loops:''' This value determines how many loops around the print will be extruded at the start.
:'''Distance from Object:''' How far from the print the loops will be extruded.
:'''Minimum Extrusion Length:''' Sets the minimum amount of filament to use when drawing the skirt loops. This will cause enough skirt loops to be drawn to use this amount of filament.
== Support Material ==
=== '''''Support Material''''' ===
:'''Generate Support Material:''' Checking the box enables the printing of support material with whatever settings you have enabled.
:'''Overhang Threshold:''' This determines the angle at which your print will have support material generated.
=== '''''Options''''' ===
:'''Pattern Spacing:''' This determines the density of your support material. Essentially the infill for it.
:'''X and Y Distance:''' How far the infill will rest away from your print on the X and Y axis. The farther away it is, the easier it is to disconnect.
:'''Z Distance:''' How far the infill will rest away from your print on the Z axis. The farther away it is, the easier it is to disconnect.
= Filament =
== Filament ==
=== '''''Filament''''' ===
:'''Diameter:''' Here you would enter the diameter of your filament. This setting is usually already entered when you first connect to a printer, giving it the default settings from the manufacturer.
=== '''''Temperature''''' ===
:'''Extruder Other Layers:''' This determines the extruder temperature for the duration of the print.
:'''Bed Other Layers:''' For printers with heat controlled beds, this determines the bed temperature for the duration of the print.
== Cooling ==
=== '''''Fan Speed''''' ===
:'''Min Fan Speed:''' This value determines the slowest speed that your fan is allowed to go, by percentage.
:'''Max Fan Speed:''' This value determines the fastest speed that your fan is allowed to go, by percentage.
:'''Disable Fan For The First:''' This determines how many layers should go by without the fan being enabled.
=== '''''Cooling Thresholds''''' ===
:'''Slow Down If Layer Print Time Is Below:''' This value determines the minimum amount of time a layer is allowed to take, in seconds. If the layer finishes before the allotted time, the extruder will move away and stop until it is allowed to resume.
= Printer =
== General ==
=== '''''Size and Coordinates''''' ===
:'''Bed Size:''' These values determine how long your bed is along each axis, by millimeters.
:'''Print Center:''' These values determine where the center of your bed lies.
:'''Build Height:''' How high your bed can lower or raise, along the Z axis.
:'''Bed Shape:''' This determines the shape of your bed, either rectangular or circular.
== Custom G-Code ==
:'''Start G-Code:''' GCode input in this field will go into effect as soon as you start a print.
:'''End G-Code:''' GCode input in this field will go into effect as soon as a print finishes.
:'''Pause G-Code:''' GCode input in this field will go into effect when the 'Pause' button is pressed during a print.
:'''Resume G-Code:''' GCode input in this field will go into effect when the 'Resume' button is pressed after the print having been paused.
:'''Cancel G-Code:''' GCode input in this field will go into effect when the 'Cancel' button is pressed during a print.
:'''On-Connect G-Code:''' GCode input in this field will go into effect when MatterControl successfully connects to the printer.
== Extruder 1 ==
=== '''''Size''''' ===
:'''Nozzle Diameter:''' This is where you input the diameter of the nozzle, in millimeters.
=== '''''Retraction''''' ===
:'''Length:''' This value determines how far your filament will be retracted with each qualifying non-printing move, in millimeters.
:'''Speed:''' This Value determines how fast your filament will be retracted, and re-extruded, in millimeters.
:'''Minimum Travel After Retraction:''' This value determines the minimum distance of a non-printing move that will result in a retraction.
[[Category:Slice Settings]]