Open main menu

User contributions

MatterHackers

31 December 2015

  • File:First Layer-ss-ex1.png

    no edit summary

    11:22

  • SETTINGS

    no edit summary

    10:07

    +613

  • SETTINGS

    no edit summary

    10:00

    +53

30 December 2015

  • SETTINGS

    no edit summary

    17:31

    +62

  • SETTINGS

    no edit summary

    17:23

    +194

  • SETTINGS

    no edit summary

    17:02

    +816

  • File:Options Menu.png

    MatterHackers uploaded a new version of File:Options Menu.png

    17:01

  • File:Options Menu.png

    MatterHackers uploaded a new version of File:Options Menu.png

    17:00

  • File:Options Menu.png

    no edit summary

    16:56

  • File:Show Help-ss.png

    MatterHackers uploaded a new version of File:Show Help-ss.png

    16:54

  • File:Settings Level Menu.png

    no edit summary

    16:51

  • File:Show Help-ss.png

    no edit summary

    16:20

  • SETTINGS

    no edit summary

    16:14

    +4

  • SETTINGS

    no edit summary

    16:14

    +5

  • LIBRARY

    ‎Downloads

    16:12

    +14

  • SETTINGS/Filament/Extrusion/Extrusion Width

    no edit summary

    16:09

    +35

  • SETTINGS/Filament/Retraction/While Printing/Wipe After Retract

    no edit summary

    16:06

    +35

  • SETTINGS/General/Output Options/File Settings/Center On Bed

    no edit summary

    16:04

    -40

  • SETTINGS/General/Support Material/Support Options/Support Everywhere

    no edit summary

    16:04

    -16

  • SETTINGS/General/Support Material/Support Material/Generate Support Material

    no edit summary

    16:03

    +50

  • SETTINGS/General/Raft-Priming/Raft/Create Raft

    no edit summary

    16:02

    +4

  • SETTINGS/General/Single Print/Settings Will Clear at End of Print/Spiral Vase

    no edit summary

    16:01

    +1

  • SETTINGS/General/Layers-Surface/Outer Surface - Perimeters/External Perimeters First

    no edit summary

    16:01

    -23

  • SETTINGS/Filament/Retraction/While Printing/Wipe After Retract

    Created page with "{{Slice Settings |The extruder will wipe the nozzle over the last up to 10 mm of tool path after retracting.|*Boolean| === Boolean === The check box is checked to use the f..."

    15:59

  • File:Wipe After Retract-ss.png

    MatterHackers moved page File:Wipe Before Retract-ss.png to File:Wipe After Retract-ss.png without leaving a redirect

    m

    15:58

  • File:Wipe After Retract-ss-ex.png

    MatterHackers moved page File:Wipe Before Retract-ss-ex.png to File:Wipe After Retract-ss-ex.png without leaving a redirect

    m

    15:57

  • File:Wipe After Retract-ss-ex1.png

    MatterHackers moved page File:Wipe Before Retract-ss-ex1.png to File:Wipe After Retract-ss-ex1.png without leaving a redirect

    m

    15:57

  • File:Wipe After Retract-ss-ex1.png

    no edit summary

    15:57

  • File:Wipe After Retract-ss-ex.png

    no edit summary

    15:56

  • SETTINGS/Filament/Retraction/While Printing/Minimum Extrusion Requiring Retraction

    Created page with "{{Slice Settings |The minimum length of filament that must be extruded before a retraction can occur.|*millimeters (mm) Can be zero.| === mm === In this example, 1.5 mm of..."

    15:02

  • File:Minimum Extrusion Requiring Retraction-ss-ex.png

    no edit summary

    15:02

  • SETTINGS/Filament/Retraction/While Printing/Minimum Travel Requiring Retraction

    Created page with "{{Slice Settings |The minimum distance of a non-print move which will trigger a retraction.|*millimeters (mm) Can be zero.| === mm === In this example, any non-print move..."

    14:56

  • SETTINGS/General/Single Print/Settings Will Clear at End of Print/Bottom Clip

    no edit summary

    14:48

    +200

  • SETTINGS/General/Single Print/Settings Will Clear at End of Print/Bottom Clip

    no edit summary

    14:46

    +18

  • SETTINGS/Filament/Retraction/While Printing/Extra Length On Restart

    Created page with "{{Slice Settings |Additional distance of filament to extrude after a retraction.|*millimeters (mm) Can be zero. Can be negative.| === mm === In this example, an additiona..."

    14:39

  • File:Extra Length On Restart-ss-ex.png

    no edit summary

    14:36

  • SETTINGS/Filament/Retraction/While Printing/Z Lift

    no edit summary

    14:32

    +14

  • SETTINGS/Filament/Retraction/While Printing/Z Lift

    Created page with "{{Slice Settings |The distance the nozzle will lift after each retraction.|*millimeters (mm)| === mm === In this example, the nozzle will lift 0.3 mm after every retraction.}}"

    14:31

  • File:Z Lift-ss-ex.png

    no edit summary

    14:31

  • SETTINGS/Filament/Retraction/While Printing/Speed

    Created page with "{{Slice Settings |The speed at which filament will retract and re-extrude until the next print move.|*millimeters per second (mm/s)| === mm/s === In this example, filament..."

    14:23

  • File:Speed-ss-ex.png

    no edit summary

    14:16

  • SETTINGS/Filament/Retraction/On Tool Change/Length on Tool Change

    Created page with "{{Slice Settings |When using multiple extruders, the distance filament will reverse before changing to a different extruder.|*millimeters (mm) Can be zer..."

    14:12

  • File:Length on Tool Change-ss-ex.png

    no edit summary

    14:12

  • SETTINGS/Filament/Retraction/While Printing/Length on Move

    no edit summary

    14:09

    +14

  • SETTINGS/Filament/Retraction/While Printing/Length on Move

    Created page with "{{Slice Settings |The distance filament will reverse before each qualifying non-print move..."

    14:07

  • File:Length on Move-ss-ex.png

    no edit summary

    14:07

  • File:Wipe After Retract-ss.png

    User created page with UploadWizard

    14:03

  • File:Length on Move-ss.png

    User created page with UploadWizard

    14:03

  • File:Z Lift-ss.png

    User created page with UploadWizard

    14:03

  • File:Minimum Travel Requiring Retraction-ss-ex.png

    User created page with UploadWizard

    14:03

older 50

  • MatterControl Manual

    • Mobile
    • Desktop
  • Privacy