Search results
Create the page "$1" on this wiki! See also the search results found.
- ...the same time, since they will conflict with each other. If MatterControl 1.5 sees that you have software leveling enabled and there is still a {{ic|G2 G1 Z1 ; raise the extruder to be 1 millimeters above the bed.7 KB (1,133 words) - 17:57, 8 February 2016
- Step 1: Open the Control Panel Step 1: Navigate to the Applications folder on your file system and delete MatterC1 KB (155 words) - 18:37, 2 February 2016
- #Raise the extruder 1 mm in z868 bytes (162 words) - 18:30, 1 February 2016
- *Use a previous version of MatterControl like 1.3: [[Release Notes#1.3.0]] === The Extruder Count must be at least 1. ===7 KB (1,128 words) - 18:10, 6 December 2016
- [[File:Getting started1.png|framed|right|Editing a printer: Step 1 (left) and 2 (right).]] ...ament > Diameter: A printer-specific setting that will not change, usually 1.75mm or 3mm.11 KB (1,822 words) - 14:48, 8 March 2016
- Step 1 - With the first part loaded, navigate to [[3D View]] and switch to [[3D Vi Step 1 - Ungroup (if needed)3 KB (513 words) - 12:50, 25 April 2017
- Starting in version 1.6, settings are automatically synced between instances of MatterControl whi ...m/articles/slice-settings-explained-part-1 SLICE SETTINGS EXPLAINED - PART 1]6 KB (882 words) - 13:35, 6 September 2018
- == Extruder 1 ==7 KB (1,045 words) - 12:44, 19 January 2016
- ...The ratio of material to empty space ranged 0 to 1. 0 would be no infill, 1 is solid infill ...'' Sets which layers will receive infill. This should normally stay set to 1 to make strong parts.16 KB (2,499 words) - 13:04, 22 December 2016
- ...es/Hardware/Extruder Count|Extruder Count]] is set to a value greater than 1.1 KB (176 words) - 11:47, 29 January 2019
- *Always run async and show progress if action will take longer than 1 s.2 KB (354 words) - 15:17, 30 November 2016
- ...plore how braille works. As of release, the Braille Builder supports Grade 1 English Braille, with support for Grade 2 slated to be added in the near fu590 bytes (88 words) - 18:08, 14 December 2015
- ...gs/{{#titleparts: {{PAGENAME}} | -1 | -2 }}|{{#titleparts: {{PAGENAME}} | -1 | -2 }}]] section of slice settings which deal with layers and surface prop912 bytes (108 words) - 13:39, 1 December 2016
- ...ers-Surface/Outer Surface - Top & Bottom/Top Solid Layers|top layers]] and 1 [[Settings/General/Layers-Surface/Outer Surface - Perimeters/Perimeters|per876 bytes (131 words) - 13:37, 1 December 2016
- Using a ratio from 0 to 1. In this case, 0.89 translates to 89%. Actual infill will be 89% of the tot738 bytes (99 words) - 12:36, 5 September 2018
- ...s/Hardware/Extruder Count|Extruder Count]].}} The first is named 'Extruder 1', the second 'Extruder 2', etc.430 bytes (60 words) - 13:59, 1 December 2016
- Not sure about how accurate this is.---->>>The second extruder (1) will be used to print the raft. See [[Extruder Index]] for more informatio500 bytes (69 words) - 18:15, 18 September 2018
- In this example, support material will be generated 1 mm away from the model on the X and Y axes.}}297 bytes (45 words) - 12:14, 31 December 2018
- ...tures/Hardware/Extruder Count|Extruder Count]] is set to a value more than 1.|*extruder index|514 bytes (68 words) - 13:30, 31 December 2018
- ...t and set to 1.08, the total result will be a multiplier of 1.1448 (1.06 * 1.08). Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; d1 KB (152 words) - 18:20, 5 April 2019
