Search results
Create the page "Slice Settings/Filament/Filament" on this wiki! See also the search results found.
- {{Migrated|slice-settings/filament/filament#density}} {{Slice Settings394 bytes (57 words) - 15:11, 7 January 2019
- {{Migrated|slice-settings/filament/retraction#extra-length-after-tool-change}} {{Slice Settings353 bytes (46 words) - 17:24, 31 May 2019
- ...e variables.</center>]]MatterSlice allows certain tokens to be placed in [[SETTINGS/Printer/Custom G-Code|custom G-Code]] that will automatically be replaced w ...code> will be replaced with the extruder temperature defined in your slice settings. These tokens can be enclosed in either square brackets [] or curly bracket3 KB (433 words) - 11:32, 28 December 2016
- {{Migrated|slice-settings/filament/advanced#extruder-wipe-temperature}} {{Slice Settings580 bytes (77 words) - 19:37, 7 January 2019
- {{Migrated|slice-settings/filament/filament#bed-temperature}} {{Slice Settings496 bytes (69 words) - 19:31, 7 January 2019
- {{Migrated|slice-settings/filament/advanced#bed-remove-part-temperature}} {{Slice Settings734 bytes (103 words) - 19:45, 7 January 2019
- {{Migrated|slice-settings/filament/retraction#retract-length}} {{Slice Settings454 bytes (54 words) - 18:49, 8 April 2019
- {{Migrated|slice-settings/filament/retraction#length-on-tool-change}} {{Slice Settings351 bytes (42 words) - 17:17, 31 May 2019
- {{Migrated|slice-settings/filament/retraction#speed}} {{Slice Settings383 bytes (54 words) - 11:28, 9 April 2019
- {{Migrated|slice-settings/filament/retraction#z-lift}} {{Slice Settings365 bytes (53 words) - 11:40, 9 April 2019
- {{Migrated|slice-settings/filament/retraction#extra-length-on-restart}} {{Slice Settings541 bytes (73 words) - 18:50, 8 April 2019
- {{Migrated|slice-settings/filament/retraction#minimum-travel-requiring-retraction}} {{Slice Settings304 bytes (39 words) - 12:03, 9 April 2019
- {{Migrated|slice-settings/filament/retraction#minimum-extrusion-requiring-retraction}} {{Slice Settings321 bytes (41 words) - 17:29, 20 May 2019
- {{Migrated|slice-settings/filament/advanced#first-layer}} {{Slice Settings796 bytes (114 words) - 18:20, 5 April 2019
- {{Migrated|slice-settings/filament/advanced#outside-perimeters}} {{Slice Settings851 bytes (119 words) - 18:25, 5 April 2019
- {{Migrated|slice-settings/speed/fan#disable-fan-for-the-first}} {{Slice Settings530 bytes (77 words) - 18:01, 13 September 2018
- {{Migrated|slice-settings\speed\cooling#slow-down-if-layer-print-time-is-below}} {{Slice Settings580 bytes (91 words) - 18:18, 13 September 2018
- {{Migrated|slice-settings/speed/cooling#minimum-print-speed}} {{Slice Settings683 bytes (106 words) - 18:45, 13 September 2018
- {{Slice Settings ...ive to the current position (G91), then move 10 mm up and retract 10 mm of filament at a rate of 12,000 mm/minute (G1 Z10 E-10 F12000), then set coordinates to593 bytes (90 words) - 13:37, 1 December 2016
- {{Slice Settings ...to the current position (G91), then move 10 mm down and extrude 10.8 mm of filament at a rate of 12,000 mm/minute (G1 Z-10 E10.8 F12000), then set coordinates631 bytes (96 words) - 13:37, 1 December 2016