Search results

Create the page "$1" on this wiki! See also the search results found.

• Template:Slice Settings
  ...upport Material). The associated file names in this template do not have a 1 at the end of the base; that is the only difference. This and [[Template:Sl <noinclude>Number 1 is the function as described in the help text, and/or Taylor's slicer setti
  1 KB (197 words) - 16:41, 2 August 2017

• File:Avoid Crossing Perimeters-ss.png |description={{en|1=Avoid Crossing Perimeters-ss}} (590 × 436 (60 KB)) - 15:36, 15 December 2015

• Automatic Print Leveling
  ...the same time, since they will conflict with each other. If MatterControl 1.5 sees that you have software leveling enabled and there is still a {{ic|G2 G1 Z1 ; raise the extruder to be 1 millimeters above the bed.
  7 KB (1,133 words) - 17:57, 8 February 2016
• Clean Install MatterControl
  Step 1: Open the Control Panel Step 1: Navigate to the Applications folder on your file system and delete MatterC
  1 KB (155 words) - 18:37, 2 February 2016
• Configuring Print Leveling
  #Raise the extruder 1 mm in z
  868 bytes (162 words) - 18:30, 1 February 2016
• Error Messages
  *Use a previous version of MatterControl like 1.3: [[Release Notes#1.3.0]] === The Extruder Count must be at least 1. ===
  7 KB (1,128 words) - 18:10, 6 December 2016
• Getting Started
  [[File:Getting started1.png|framed|right|Editing a printer: Step 1 (left) and 2 (right).]] ...ament > Diameter: A printer-specific setting that will not change, usually 1.75mm or 3mm.
  11 KB (1,822 words) - 14:48, 8 March 2016

• File:Bottom Clip-ss.png |description={{en|1=Bottom Clip-ss}} (597 × 250 (35 KB)) - 14:15, 17 November 2016

• File:Bottom Solid Layers-ss.png |description={{en|1=Bottom Solid Layers-ss}} (590 × 436 (59 KB)) - 16:37, 15 December 2015

• File:External Perimeters First-ss.png |description={{en|1=External Perimeters First-ss}} (590 × 436 (60 KB)) - 16:25, 15 December 2015

• File:First Layer Height-ss.png |description={{en|1=First Layer Height-ss}} (590 × 436 (58 KB)) - 18:20, 15 December 2015

• File:Spiral Vase-ss.png |description={{en|1=Spiral Vase-ss}} (590 × 436 (59 KB)) - 16:15, 15 December 2015

• File:Layer Height-ss.png |description={{en|1=Layer Height-ss}} (590 × 436 (57 KB)) - 15:37, 15 December 2015

• File:Top Solid Layers-ss.png |description={{en|1=Top Solid Layers-ss}} (590 × 436 (59 KB)) - 16:35, 15 December 2015

• File:First Layer Height-ss-ex1.png |description={{en|1=First Layer Height-ss-ex1}} (403 × 140 (12 KB)) - 12:33, 17 December 2015

• Multi-Extrusion
  Step 1 - With the first part loaded, navigate to [[3D View]] and switch to [[3D Vi Step 1 - Ungroup (if needed)
  3 KB (513 words) - 12:50, 25 April 2017
• SETTINGS
  Starting in version 1.6, settings are automatically synced between instances of MatterControl whi ...m/articles/slice-settings-explained-part-1 SLICE SETTINGS EXPLAINED - PART 1]
  6 KB (882 words) - 13:35, 6 September 2018
• CuraEngine Settings
  == Extruder 1 ==
  7 KB (1,045 words) - 12:44, 19 January 2016
• Slic3r Settings
  ...The ratio of material to empty space ranged 0 to 1. 0 would be no infill, 1 is solid infill ...'' Sets which layers will receive infill. This should normally stay set to 1 to make strong parts.
  16 KB (2,499 words) - 13:04, 22 December 2016
• OPTIONS/Slice Engine
  ...es/Hardware/Extruder Count|Extruder Count]] is set to a value greater than 1.
  1 KB (176 words) - 11:47, 29 January 2019

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)