Search results
Create the page "Slice Settings/Filament" on this wiki! See also the search results found.
- Slices the current model using the [[Settings|slice settings]] and displays the tool path. ==== Filament Length ====4 KB (636 words) - 10:30, 1 November 2017
- ...cing larger models (250,000+ polygons) to 100,000 generally allows them to slice well and causes no significant loss to printable resolution. Here's a link == Slice Errors ==7 KB (1,128 words) - 18:10, 6 December 2016
- ...the 'Edit' link next to your recently added printer, and double check the settings. ...d is only generated on demand - to create the layer view with your current settings click the 'Generate' button.11 KB (1,822 words) - 14:48, 8 March 2016
- ...gs -> Printer` as well as a few under `Settings & Controls -> Settings -> Filament`. On the MatterControl Touch, go to OPTIONS. Under Application Settings, switch the '''Update Notification Feed''' to Beta or Alpha.11 KB (1,793 words) - 17:53, 5 December 2016
- *Added filament selection into leveling wizard so we heat to printing temp before sampling. *Added support for filament run out sensor25 KB (3,207 words) - 15:22, 7 June 2019
- {{Migrated|slice-settings/filament/retraction#retract-when-changing-islands}} {{Slice Settings345 bytes (44 words) - 17:03, 20 May 2019
- ...ent/Cooling/Fan Speed/Minimum Fan Speed|Minimum Fan Speed]] and [[SETTINGS/Filament/Cooling/Fan Speed/Maximum Fan Speed|Maximum Fan Speed]] to 0. ...e. The properties will change depending on which [[:Category:Slice Engines|slice engine]] you use.3 KB (471 words) - 14:03, 1 December 2016
- {{Migrated|slice-settings/index}} ...low you will find links to the categories, sub-categories, and sections of settings for [[MatterSlice]], as well as information about the menus and options ava6 KB (882 words) - 13:35, 6 September 2018
- The slice settings for CuraEngine in MatterControl are divided by three categories: * '''General''': This is where the settings concerning the actual printed part are located. Things like, layer height,7 KB (1,045 words) - 12:44, 19 January 2016
- The slice settings for Slic3r in MatterControl are divided by three categories: * '''General''': This is where the settings concerning the actual printed part are located. Things like, layer height,16 KB (2,499 words) - 13:04, 22 December 2016
- ...ng a value in the related field, or from the respective value in the slice settings. ...ols the temperature of the nozzle. If multiple extruders are present and [[Settings/Printer/Features/Hardware/Extruder Count|specified]], a section appears for3 KB (408 words) - 11:53, 4 September 2018
- {{Migrated|slice-settings/filament/index}} ...ings pane.</center>]]Slice Settings found under this category apply to the filament used to create the print.596 bytes (67 words) - 19:31, 4 January 2019
- {{Migrated|slice-settings/filament/advanced}} {{Slice Settings Category|how the filament is extruded during certain phases of a print.}}394 bytes (44 words) - 18:26, 5 April 2019
- {{Slice Settings Category|fans and other methods for keeping the print at the right temperat === [[SETTINGS/Filament/Cooling/Fan_Speed|Fan Speed]] ===373 bytes (44 words) - 13:53, 1 December 2016
- {{Slice Settings Category|filament the print will use.}} === [[SETTINGS/Filament/Retraction/While_Printing|While Printing]] ===350 bytes (40 words) - 13:52, 1 December 2016
- {{Slice Settings Subsection|filament size and rate of extrusion.}}66 bytes (9 words) - 13:37, 1 December 2016
- {{Migrated|slice-settings/adhesion/skirt#minimum-extrusion-length}} {{Slice Settings735 bytes (123 words) - 12:10, 14 September 2018
- {{Migrated|slice-settings/filament/filament#diameter}} {{Slice Settings393 bytes (51 words) - 19:47, 4 January 2019
- {{Migrated|slice-settings/filament/advanced#extrusion-multiplier}} {{Slice Settings1 KB (152 words) - 18:20, 5 April 2019
- {{Migrated|slice-settings/filament/filament#extruder-temperature}} {{Slice Settings530 bytes (68 words) - 19:12, 7 January 2019
