User contributions
7 January 2016
5 January 2016
Automatic Print Leveling
no edit summary
Automatic Print Leveling
no edit summary
+11
SETTINGS/Printer/Custom G-Code/Start G-Code
Redirected page to Start GCode
+2
Template:Hc
Created page with "<noinclude>{{DISPLAYTITLE:Template:hc}} {{Template}} '''Block code with header.''' * Use Template:bc for block code without header. * Use Template:ic for inline code..."
Template:Bc
Created page with "<noinclude>{{DISPLAYTITLE:Template:bc}} {{Template}} '''Block code without header.''' * Use Template:hc for block code with header. * Use Template:ic for inline code..."
Frequently Asked Questions
no edit summary
+39
Frequently Asked Questions
no edit summary
+879
Template:Ic
Created page with "<noinclude>{{Template}} {{DISPLAYTITLE:Template:ic}} '''Inline code.''' * Use Template:bc for block code without header. * Use Template:hc for block code with header..."
4 January 2016
SETTINGS
Show Help
-20
SETTINGS/Filament/Cooling
no edit summary
-13
SETTINGS/Filament/Cooling
no edit summary
+1
31 December 2015
SETTINGS/Filament/Cooling/Cooling Thresholds/Minimum Print Speed
Created page with "{{Slice Settings |The minimum speed to which the printer will reduce in order to attempt to make the layer print time long enough to satisfy the Slice Settings/Filament/Coo..."
File:Minimum Print Speed-ss-ex.png
no edit summary
SETTINGS/Filament/Cooling/Cooling Thresholds/Slow Down If Layer Print Time Is Below
Created page with "{{Slice Settings |The minimum amount of time a layer must take to print. If a layer will take less than this amount of time, the movement speed is reduced so the layer print..."
File:Slow Down If Layer Print Time Is Below-ss-ex.png
no edit summary
SETTINGS/Filament/Cooling/Fan Speed/Disable Fan For The First
Created page with "{{Slice Settings |The number of layers for which the layer cooling fan will be forced off at the start of the print.|*count (layers) Can be zero.| === layers === In th..."
File:Disable Fan For The First-ss-ex.png
no edit summary
SETTINGS/Filament/Cooling/Fan Speed/Bridging Fan Speed
Created page with "{{Slice Settings |The speed at which the layer cooling fan will run when bridging, expressed as a percentage of full power.|*percent (%) Can be zero.| === % === In..."
File:Bridging Fan Speed-ss-ex.png
no edit summary
SETTINGS/Filament/Cooling/Fan Speed/Maximum Fan Speed
Created page with "{{Slice Settings |The maximum speed at which the layer cooling fan will run, expressed as a percentage of full power.|*percent (%) Can be zero.| === % === In this exam..."
File:Maximum Fan Speed-ss-ex.png
no edit summary
SETTINGS/Filament/Cooling/Fan Speed/Minimum Fan Speed
Created page with "{{Slice Settings |The minimum speed at which the layer cooling fan will run, expressed as a percentage of full power.|*percent (%) Can be zero.| === % === In this exam..."
File:Minimum Fan Speed-ss-ex.png
no edit summary
File:Slow Down If Layer Print Time Is Below-ss.png
User created page with UploadWizard
File:Minimum Print Speed-ss.png
User created page with UploadWizard
File:Minimum Fan Speed-ss.png
User created page with UploadWizard
File:Maximum Fan Speed-ss.png
User created page with UploadWizard
File:Disable Fan For The First-ss.png
User created page with UploadWizard
File:Bridging Fan Speed-ss.png
User created page with UploadWizard
SETTINGS/Filament/Extrusion/Extrusion Width/Support Material
no edit summary
+1
SETTINGS/Filament/Extrusion/Extrusion Width/First Layer
no edit summary
+1
SETTINGS/Filament/Extrusion/Extrusion Width/Outside Perimeters
no edit summary
+1
SETTINGS/Filament/Extrusion/Extrusion Width/Support Material
Created page with "{{Slice Settings |A modifier of the width of the extrusion when printing support material.|*millimeters (mm) *..."
File:Support Material-ss-ex.png
no edit summary
File:Support Material-ss-ex1.png
no edit summary
SETTINGS/Filament/Extrusion/Extrusion Width/Outside Perimeters
no edit summary
SETTINGS/Filament/Extrusion/Extrusion Width/Outside Perimeters
Created page with "{{Slice Settings |A modifier of the width of the extrusion when printing outside perimeters. Can be useful to..."
SETTINGS/Filament/Extrusion/Extrusion Width/First Layer
no edit summary
+6
File:Outside Perimeters-ss-ex1.png
no edit summary
File:Outside Perimeters-ss-ex.png
MatterHackers uploaded a new version of File:Outside Perimeters-ss-ex.png
File:Outside Perimeters-ss-ex.png
no edit summary
SETTINGS/Filament/Extrusion/Extrusion Width/First Layer
Created page with "{{Slice Settings |A modifier of the width of the extrusion for the first layer of the print. A value greater th..."
File:Support Material-ss.png
User created page with UploadWizard
File:Outside Perimeters-ss.png
User created page with UploadWizard
File:First Layer-ss.png
User created page with UploadWizard
File:First Layer-ss-ex1.png
MatterHackers uploaded a new version of File:First Layer-ss-ex1.png
File:First Layer-ss-ex.png
MatterHackers uploaded a new version of File:First Layer-ss-ex.png
File:First Layer-ss-ex.png
no edit summary