Search results

Jump to: navigation, search

Create the page "Firmware" on this wiki! See also the search results found.

Page title matches

Page text matches

  • Automatic Print Leveling
    ...with some kind of probe or sensor for measuring the height of the bed. The firmware then takes into account these measurements when executing moves. The probin ==== Firmware Changes: ====
    7 KB (1,133 words) - 16:57, 8 February 2016
  • OPTIONS/EEProm
    MatterControl supports interacting with EEPROM as allowed by the firmware-- Marlin and Repetier only. == Firmware Support ==
    2 KB (211 words) - 14:21, 2 August 2017
  • OPTIONS
    If the printer's firmware supports [[EEProm]], the settings can be adjusted here.
    2 KB (231 words) - 13:08, 1 December 2016
  • Send Debugging Information
    ...ween MatterControl and your printer. It is helpful for diagnosing hardware/firmware errors and communications issues.
    4 KB (654 words) - 08:27, 13 September 2017
  • Frequently Asked Questions
    == When I restart my printer, values of Steps per mm return to the firmware's default value. How can I change this? == It is likely your printer's firmware does not allow EEPROM to be saved.
    11 KB (1,793 words) - 16:53, 5 December 2016
  • Release Notes
    *Now reporting bed and extruder heating state for Repetier firmware
    25 KB (3,207 words) - 14:22, 7 June 2019
  • Slic3r Settings
    === '''''Firmware''''' === :'''G-Code Flavor''' Some firmware uses different g and m codes. Setting this ensures that the output G-Code w
    16 KB (2,499 words) - 12:04, 22 December 2016
  • SETTINGS/Printer/Features/Behavior
    {{Slice Settings Subsection|options for interacting with the firmware installed on the printer.}}
    97 bytes (13 words) - 12:37, 1 December 2016
  • SETTINGS/Printer/Extruder/Extruder X/Extruder Offset
    ...ltiple extruder machines. Some dual extruder machines handle the offset in firmware, in which case it should be set to 0,0 in MatterControl. If the second extr
    691 bytes (122 words) - 12:37, 1 December 2016
  • CONTROLS
    == [[CONTROLS/Firmware Updater|Firmware Updater]] == Allows the user to update an Arduino-based printer's firmware from within MatterControl.
    2 KB (249 words) - 10:57, 4 September 2018
  • SETTINGS/Printer/Connection/Details/Baud Rate
    |The serial port communication speed of the printers firmware.|*bits per second (bps)|
    230 bytes (33 words) - 12:37, 1 December 2016
  • SETTINGS/Printer/Features/Interface/Show Firmware Updater
    |Toggles display and use of the [[CONTROLS/Firmware Updater|Firmware Updater]] section shown in the CONTROLS pane.|Available as presets only:
    235 bytes (33 words) - 16:53, 1 December 2016
  • Settings/Printer/Features/Firmware
    #REDIRECT [[SETTINGS/Printer/Features/Firmware]]
    48 bytes (5 words) - 12:37, 1 December 2016
  • Settings/Printer/Features/Firmware/Allow Negative Z
    #REDIRECT [[SETTINGS/Printer/Features/Firmware/Allow Negative Z]]
    65 bytes (8 words) - 12:37, 1 December 2016
  • Settings/Printer/Features/Firmware/Z Can Be Negative
    #REDIRECT [[SETTINGS/Printer/Features/Firmware/Z Can Be Negative]]
    66 bytes (9 words) - 12:37, 1 December 2016
  • Settings/Printer/Features/Interface/Show Firmware Updater
    #REDIRECT [[SETTINGS/Printer/Features/Interface/Show Firmware Updater]]
    71 bytes (8 words) - 12:37, 1 December 2016
  • SETTINGS/Printer/Features/Hardware/Networked Printing
    ...i/Serial adapter running the [https://github.com/jeelabs/esp-link ESP-Link firmware].
    1 KB (199 words) - 17:14, 31 July 2017
  • SETTINGS/Printer/Features/Hardware/Has Filament Runout Sensor
    For this feature to work, the firmware must support reporting the status of the runout sensor using the M119 comma
    600 bytes (97 words) - 16:11, 31 July 2017
\n

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "http://wiki.mattercontrol.com/Special:Search/Firmware"